Midi-solutions Footswitch Controller Instrukcja Użytkownika Strona 6

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 14
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 5
6
CONTROLCHANGE
START/STOP
ToprogramtheFootswitchControllertosendoutuptoeightControlChange(CC)messageswhenthefootswitchis
depressed,senditthefollowingSystemExclusiveprogrammingcommand:
( and areoptional)
AllbytesmustbeinHexadecimalformat(seehexadecimalconversiontableatend)
specifiesmodeoftransmissionasfollows:
02:SendCC(s)ondepressionoffootswitch,CC(s)ofvalue0onrelease
12:SendCC(s)ondepressionoffootswitch,nothingonrelease
22:SendCC(s)ondepressionoffootswitch,CC(s)ofvalue0afterthedurationspecifiedby (seebelow)
32:SendCC(s)ondepressionoffootswitch,CC(s)ofvalue0whenthefootswitchisreleasedafterthe
minimumduration (seebelow)
42:SendCC(s)ondepressionoffootswitch,CC(s)ofvalue0whenthefootswitchisreleaseduptothe
maximumduration (seebelow)
52:CyclethrougheachCCondepressionoffootswitch,sendthecorrespondingCCofvalue0onrelease
62:CyclethrougheachCCondepressionoffootswitch,sendnothingonrelease
=Durationin8msincrements,or1sincrementsifprecededby00.( isonlyincludedif =22,32,or42)
=ControlChangenumber
=ControlChangevalue(sentondepressionoffootswitch)
=MIDIchannel(seeMIDIchanneltableatend)
=AdditionalCCnumbersandvalues(uptoeightCCstotal)
ToprogramtheFootswitchControllertosendmaximumvolumeonallMIDIchannelswhenthefootswitchis
depressed,set (SendCCondepressionoffootswitch,nothingonrelease), (volumeisCC#7),
(7Fisthehexadecimalvaluefor127,themaximumvalue),and (7FspecifiesallMIDIchannels).These
valuesresultinthefollowingSystemExclusiveprogrammingcommand:
F000005004 F7
ToprogramtheFootswitchControllertosendMIDIStartandStopmessages,senditthefollowingSystemExclusive
programmingcommand:
( isoptional)
specifiesthemodeoftransmissionasfollows:
00:SendStopondepressionoffootswitch,nothingonrelease
01:SendStartondepressionoffootswitch,nothingonrelease
omitted:SendStartondepressionoffootswitch,Stoponrelease
NotethattheFootswitchControllercanbeprogrammedtotogglebetweenStartandStopeachtimethefootswitchis
depressedbysettingtheFootswitchToggleparametertoToggleON(seeDeviceParameters).
F000005004aa(tt)nnvvcc(nnvv)F7 tt nnvv
aa
tt
tt
tt
tt tt aa
nn
vv
cc
nnvv
Example
aa=12 nn=07 vv=
7F cc=7F
12077F7F
F00000500405(ss)F7 ss
ss
ss
Przeglądanie stron 5
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Komentarze do niniejszej Instrukcji

Brak uwag